IPB

( Log In ) Log In is for TREC Teachers & Researchers only

 
Reply to this topicStart new topic
> A Full Day, Starting With A Multicore Sample, What's down there anyway?
Steve_Marshall
post Jun 22 2005, 11:41 PM
Post #1


TREC Teacher
***

Group: TREC Team
Posts: 78
Joined: 27-April 05
Member No.: 12



Monday 6/20/05 #1
A FULL DAY, STARTING WITH A MULTICORE SAMPLE


After a slow start with the first piston core yesterday, the work done today definitely resulted in some fast catching up and a full day of science research. The menu for today was a multi-core sample, another piston core, two plankton tows, and a CTD profile. Because there is so much involved with each type of experiment, I will relate these with separate journal entries. This one will describe the multi-core sampling. Before describing the details of the collection and the resulting research, I should probably explain what a multi-core is, and how it compares to the piston core. The piston core is a single core that is usually much larger than the multicore (our piston cores have ranged from 20 to 60 meters in length). The multi-core samples are much smaller, about 70cm maximum, but there are up to eight separate 70cm cores on a single deployment of the multicore assembly. Another advantage of the multicore is that these samples will be studied immediately on the ship, while the piston core sections will not be analyzed until the ship returns to land.

Big Size Difference
IPB Image
This is just PART of the piston core. Use this to compare the lengths of the piston core to a multi-core sample (shown a few pictures below).

Because the multi-core is also an important part of this research cruise, I will go into some detail to describe the process, using pictures to help with the explanation:

Waiting
IPB Image
Members of the science party wait for the multi-core assembly to be brought back to the surface. Note the ever-present ice patrol (person holding the long pole) needed to keep ice away from the multi-core also

Getting Close
IPB Image
The first to arrive on the line is a Niskin bottle. This bottle takes water samples that can be studied in different ways. It’s arrival indicates the multicorer is not far behind.

Looks More Like an Alien Spacecraft to Me!
IPB Image
The multicore assembly pictured as it just comes out of the water. It may be a little hard to see, but the actual core samples are the vertical cylindrical tubes towards the center of the assembly

Hauling in the Catch
IPB Image
The researchers bring the multicorer to the deck. With people in the picture, this gives you a good sense of scale about the size of the multicore tubes. Remember to compare them to the size of the PARTIAL piston core shown in the picture at the beginning of this journal entry.

Secure Storage
IPB Image
Once the multicore assembly is brought on deck, the individual tubes are removed and secured to a rack labeled with the corresponding number printed on the cores.

Attaching the Cores
IPB Image
Glenn Berger is shown here fastening one of the core samples to the rack.

What’s That Number Again?
IPB Image
The first order of business is to record the length of the cores since they can vary in the amount of sediment each holds. Here, I’m recording the measurements made and called out to me by Stefanie Brachfeld

The Liner Lady
IPB Image
Lyanne Yurco is shown here holding some of the core liners that the multicores must be transferred into; A process that is called “extruding the core.”

Setting up the Extrusion Process
IPB Image
The core sample is placed on a vertical rack. A liner (the clear tube on top) is then placed above the core sample. A retractable “leg” which has held the sediment in the tube to this point is returned to the “open” position (shown to the right, midway between the core sample and the empty liner), while a metal plate (shown at the bottom of the tube) is used to hold the sediment in the tube until the extracting piston can be put in place.

Putting the Piston into Place
IPB Image
Pictured in the middle, Glenn Berger positions the extrusion piston at the bottom of the core sample tube (just below the metal plate that Lyanne is holding. This piston sits on top of a shaft that can be raised or lowered using a drill.

Extruding the Core
IPB Image
Once the piston has been inserted far enough into the sample to create an air and water-tight seal, a drill raises the piston into the tube, thus transferring the core sample to the core liner. The liner is then capped (as shown being done here by Guillaume) on the top and then the bottom.

Filling In the Empty Space
IPB Image
If the sediment does not fill the entire tube, foam plugs are used to fill in the empty space to prevent movement and mixing of the sediment. Here, Glenn Berger and Stefanie Brachfeld measure the amount of foam needed to fill the core liner.

Once the cores are all extruded, logged, and labeled, the scientists could begin their work. I think I mentioned in a previous journal entry that I was amazed at how many different ways a core could be analyzed, but now I was seeing it in action. My next journal entry will be a summary of only a few of those methods.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- NSF Acknowledgment & Disclaimer Time is now: 27th August 2016 - 03:05 AM
IPS Driver Error  

There appears to be an error with the database.
You can try to refresh the page by clicking here.

Error Returned

We apologise for any inconvenience